Parking Brake

I installed the parking brake today. Nothing too big to note, a lot of people have already covered installing the PVPV-D, so enjoy the photo:

Final tail to fuselage mating

I spent the last couple of days cleaning the shop and getting parts organized (something that piled up on me). Today I felt it was time to get things on the plane itself moving. Over the last couple of nights I got all of the priming, deburring, and dimpling on both the tail and mid-fuse skins and bulkheads done. Everything was set to bring the tail and fuselage back together for riveting!

The last photo before the two parts permanently become one (hopefully for a long time!)

 

Christie was at the movies with Mackenzie and I could not wait to get things moving so I fumbled around for 45 minutes and finally got the two assemblies lined up.

I clecoed everything up and triple checked the skin alignments. I noticed when I was taking the tail off of the fuselage on initial fit-up that one of the mid-fuse bottom skins got under the tail skin and it should be the other way around. So make sure to double check all the corners of the skin fit ups.

I set the side skin rivets and then skipped forward a couple of steps to rivet some of the ribs. I am going to need someone inside of the plane laying on the ribs in order to help buck, so I felt it was better to stiffen up some of the ribs before putting weight on them.

Just another day of riveting.

Beringer Brake Kit Arrival

A couple of months back I started looking at items that I wanted to delete out of my finishing kit in order to purchase upgraded parts. The wheels, tires, and brakes were on the cut list. I was
planning on purchasing the Matco main wheel kit for the RV10 and probably putting the Beringer nose wheel on.

In early February I came across the following flyer:


I realize that the full Beringer main and nose wheel kits are probably a little over the top for my build, but after speaking to a few people who recently upgraded from the Matco wheel kit to the Beringer, the special offer savings started to look a little more attractive. In late February I bit the bullet, emailed EAA 186 to see if anyone else was planning on using the offer, and when I heard that nobody was I purchased the kit. Beringer US initially quoted that the wheels would come in late March. In early March I received an email that the wheels were going to ship!

The fit and finish on all of the parts looks amazing. This is a really nice setup! The one thing I did not order was the Beringer parking brake. I already had the Matco PVPV-D, and additionally I had already milled a bracket for that parking brake. 

Work Weekend

I know this is pretty boring for everyone to watch, but I started to post these in order to record the memories.

Heater bypass valve comparison

One of the complaint I have always read about on the -10 was the VANS heater boxes. Some people complained that they leaked a lot, others complained that they were made of aluminum (too low of a melting point), others complained just to complain.

I will admit, that prior to getting my fuselage (and thus Vans heater boxes) I was not planning on upgrading the boxes. People will complain about anything and heater boxes are pretty simplistic mechanical devices, so I figured the Vans units were just fine.

Then my fuselage arrived and when I inventoried the boxes I had second thoughts. Again, these are pretty simple things, with that said, there is no reason to not have high quality parts here.

On the left is the stainless steel part that I order from Aircraft Spruce (Part # 08-06230) and on the right is the part that Vans ships with the fuselage kit. I may be wrong, but I think the aircraft spruce parts are just the Plane Innovations parts.




You will notice a couple of things. One, the Plane Innovations unit is stainless steel. It has nicely spot welded connections, the larger flat area on the flapper has some stiffening ribs pressed in (which I am sure help a lot with warping when heated), and finally the flapper and door have a 90 degree frame on them that look like they will do a much better job of closing out completely.



All in all I am happy with the Plane Innovation units. I will be installing them! As an added benefit, these things will take a bunch of heat in the unfortunate event of an engine fire. (Image from Plane Innovations).

Fuselage to Tail mating

I think there are two events that are something that I have really been looking forward to. One is the completion of the canopy and doors with the other being the mating of the tail to fuselage. It was finally time to tackle one of those!


We started with getting the tail lined up to the fuselage. Thankfully the tail is pretty light and easy to maneuver. That doesn't mean however that it is not a pain in the butt to get the two to line up so that you can get enough clecos in to have the fuselage support the tail. What seemed to work well for us was to support the tail aft (around where the rudder brackets are) from a line suspended from the ceiling, and then block the forward part of the tail up to a height pretty close to the fuselage height. This allowed for enough movement of the tail to shimmy everything into place.











With the tail and fuse skins clecoed the ribs could be final drilled. The threaded 90 degree drill was a live saver with these holes.

With that done, the fuselage and tail longerons could be drilled and bolted. 

Fuselage Inventory

With the fuselage safely on the jig and able to move around the shop, now it is time to start unpacking all of the parts! It is February and a little cold, so I brought my screw bins into the house to do the small item inventory.

For the main parts inventory I found myself a little helper. This is really the first time Mack has been able to have a legit job on the plane. She was able to unwrap, call off part numbers, and re-organize all of the components. I think she actually had fun doing it too!